Production Engineer Interview Questions And Answers

Download Production Engineer Interview Questions and Answers PDF

Refine your Production Engineer interview skills with our 52 critical questions. These questions are specifically selected to challenge and enhance your knowledge in Production Engineer. Perfect for all proficiency levels, they are key to your interview success. Get the free PDF download to access all 52 questions and excel in your Production Engineer interview. This comprehensive guide is essential for effective study and confidence building.

52 Production Engineer Questions and Answers:

Production Engineer Job Interview Questions Table of Contents:

Production Engineer Job Interview Questions and Answers

1 :: Segmental chips are formed during machining:
A. mild steel
B. cast iron
C. high speed steel
D. high carbon steel

B. cast iron

2 :: If the diameter of the hole is subject to considerable variation, then for locating in jigs and fixtures, the pressure type of locator used is:

A. conical locator
B. cylindrical locator
C. diamond pin locator
D. vee locator

A. conical locator

3 :: Side rake angle of a single point cutting tool is the angle:

A. by which the face of the tool is inclined towards back
B. by which the face of the tool is inclined sideways
C. between the surface of the flank immediately below the point and a plane at right angles to the centre line of the point of the tool
D. between the surface of the flank immediately below the point and a line drawn from the point perpendicular to the base

B. by which the face of the tool is inclined sideways

4 :: Cemented carbide tool tips are produced by powder metallurgy.

A. True
B. False

A. True

5 :: In order to prevent tool from rubbing the work __________ on tools are provided.

A. rake angles
B. relief angles

B. relief angles

6 :: The silicon carbide abrasive is chiefly used for grinding:

A. cemented carbide
B. ceramic
C. cast iron
D. all of these

D. all of these

7 :: Drilling is an example of:

A. orthogonal cutting
B. oblique cutting
C. simple cutting
D. uniform cutting

B. oblique cutting

8 :: A round nose tool may be fed either from left to right end or from right to left end of the lathe bed.
A. Yes
B. No

A. Yes

9 :: When the cutting edge of the tool is dull, then during machining:

A. continuous chips are formed
B. discontinuous chips are formed
C. continuous chips with built-up edge are formed
D. no chips are formed

C. continuous chips with built-up edge are formed

10 :: Internal gears can be made by:

A. hobbing
B. shaping with pinion cutter
C. shaping with rack cutter
D. milling

B. shaping with pinion cutter

11 :: Cast iron during machining produces

A. continuous chips
B. discontinuous chips
C. continuous chips with built-up-edge
D. none of these

B. discontinuous chips

12 :: A single point thread cutting tool should ideally have:

A. zero rake angle
B. positive rake angle
C. negative rake angle
D. point angle

A. zero rake angle

13 :: A fine grained grinding wheel is used to grind hard materials.

A. Correct
B. Incorrect

A. Correct

14 :: The cutting tool in a milling machine is mounted on:

A. spindle
B. arbor
C. column
D. knee

B. arbor

15 :: The tool made of cemented carbide wear out faster at:

A. slow speeds
B. medium speeds
C. fast speeds
D. very fast speeds

A. slow speeds

16 :: A push broach as compared to pull broach:

A. has less number of teeth
B. is short and stocky
C. removes less material for each pass of the tool
D. all of the above

D. all of the above

17 :: The work or surface speed for cylindrical grinding varies from

A. 5 to 10 m/min
B. 10 to 20 m/min
C. 20 to 30 m/min
D. 40 to 60 m/min

C. 20 to 30 m/min

18 :: A twist drill is a:

A. side cutting tool
B. front cutting tool
C. end cutting tool
D. none of these

C. end cutting tool

19 :: The rake angle required to machine brass by high speed steel tool is:

A. 0°
B. 10°
C. 20°
D. -10°

A. 0°

20 :: Twist drills are made of:

A. high speed steel
B. carbon steel
C. stainless steel
D. either (a) or (b)

D. either (a) or (b)

21 :: The average cutting speed for turning brass with a high speed steel tool is:

A. 15 to 19 m/min
B. 25 to 31 m/min
C. 60 to 90 m/min
D. 90 to 120 m/min

C. 60 to 90 m/min

22 :: Side rake angle on tools is provided to control chip flow.

A. True
B. False

A. True

23 :: The maximum production of small and slender parts is done by:

A. watch maker's lathe
B. sliding head stock automatic lathe
C. multispindle automatic lathe
D. capastan lathe

C. multispindle automatic lathe

24 :: The lip angle of a single point tool is usually:

A. 20° to 40°
B. 40° to 60°
C. 60° to 80°
D. none of these

C. 60° to 80°

25 :: A fixture does not guide the tool.

A. Correct
B. Incorrect

A. Correct

Production Engineer Interview Questions And Answers

Download Production Engineer Interview Questions and Answers PDF

52 Production Engineer Questions and Answers:

Production Engineer Job Interview Questions Table of Contents:

1 :: Segmental chips are formed during machining: A. mild steel B. cast iron C. high speed steel D. high carbon steel

2 :: If the diameter of the hole is subject to considerable variation, then for locating in jigs and fixtures, the pressure type of locator used is: A. conical locator B. cylindrical locator C. diamond pin locator D. vee locator

4 :: Cemented carbide tool tips are produced by powder metallurgy. A. True B. False

5 :: In order to prevent tool from rubbing the work __________ on tools are provided. A. rake angles B. relief angles

6 :: The silicon carbide abrasive is chiefly used for grinding: A. cemented carbide B. ceramic C. cast iron D. all of these

7 :: Drilling is an example of: A. orthogonal cutting B. oblique cutting C. simple cutting D. uniform cutting

8 :: A round nose tool may be fed either from left to right end or from right to left end of the lathe bed. A. Yes B. No

9 :: When the cutting edge of the tool is dull, then during machining: A. continuous chips are formed B. discontinuous chips are formed C. continuous chips with built-up edge are formed D. no chips are formed

10 :: Internal gears can be made by: A. hobbing B. shaping with pinion cutter C. shaping with rack cutter D. milling

11 :: Cast iron during machining produces A. continuous chips B. discontinuous chips C. continuous chips with built-up-edge D. none of these

12 :: A single point thread cutting tool should ideally have: A. zero rake angle B. positive rake angle C. negative rake angle D. point angle

13 :: A fine grained grinding wheel is used to grind hard materials. A. Correct B. Incorrect

14 :: The cutting tool in a milling machine is mounted on: A. spindle B. arbor C. column D. knee

15 :: The tool made of cemented carbide wear out faster at: A. slow speeds B. medium speeds C. fast speeds D. very fast speeds

16 :: A push broach as compared to pull broach: A. has less number of teeth B. is short and stocky C. removes less material for each pass of the tool D. all of the above

17 :: The work or surface speed for cylindrical grinding varies from A. 5 to 10 m/min B. 10 to 20 m/min C. 20 to 30 m/min D. 40 to 60 m/min

18 :: A twist drill is a: A. side cutting tool B. front cutting tool C. end cutting tool D. none of these

19 :: The rake angle required to machine brass by high speed steel tool is: A. 0° B. 10° C. 20° D. -10°

20 :: Twist drills are made of: A. high speed steel B. carbon steel C. stainless steel D. either (a) or (b)

21 :: The average cutting speed for turning brass with a high speed steel tool is: A. 15 to 19 m/min B. 25 to 31 m/min C. 60 to 90 m/min D. 90 to 120 m/min

22 :: Side rake angle on tools is provided to control chip flow. A. True B. False

23 :: The maximum production of small and slender parts is done by: A. watch maker's lathe B. sliding head stock automatic lathe C. multispindle automatic lathe D. capastan lathe

24 :: The lip angle of a single point tool is usually: A. 20° to 40° B. 40° to 60° C. 60° to 80° D. none of these

25 :: A fixture does not guide the tool. A. Correct B. Incorrect