Automobile Engineering Interview Questions And Answers

Tractors have big rear tires because ,the larger the surface
area of the tractor's wheels touching the ground, the more
pulling power you have. Like how tractor pullers have large
tires.

Another reason is that the tractor doesn't have to operate
at a higher speed to get the same ground speed with larger
tires. Gear ratios don't have to be as high b/c of the
larger tires.

A geometric parameter which is positive if the kingpin axis
intersects the wheel plane at or below ground level, or is
negative if the point of intersection is above ground level.
Also called scrub radius

Boiler horse power (BHP) is a power unit used for measuring the power output of boilers, widely used in the past, but now confined to North America. The boiler horsepower conversion formula is as follows.

1 Boiler Horsepower = 9,809.5 Watts

In a two stroke engine, for every two rotations of the crank
shaft there will be one power stroke.Hence during
compression stroke, fuel will be drawn in to the crank case
(suction) and during power stroke, burnt fuel will be thrown
out through transfer ports (exaust).
In a four stroke engine, for every four rotations of the
crank shaft there will be one power stroke.
Here, suction, compression,power & exaust strokes are seperate
as there will be inlet and exaust valves.

spray painting it is generally used for painting in a very
smaller areas of any part and where it is very hard to paint
in a brush .... And to improve faster rate of painting,,
spray painting r used........usually reciprocating
compressor r used but size depends upon requirement...........

No, the type of fitting & design does not vary for automotive
segment. Its the same. However, its different in case of
aerospace & other sector.
In the fittings, usually of hole/shaft one of those is made at
the basic size so that it can accommodate the other one.

yes, absolutely .. It leads to higher wear and tear in
cyclinder liners,piston and damage of the piston .. It even
leads to knocking and detonation where abnormal combustion
appears and dark smoke and harsh sound will be produced by
the engine.

BHP stands for Brake horse power
As the name implies it is the braking power required to
stall a engine Means horse power required to stop engine
rotation

IN BS2 there is No catalytic converter to reduce formation
of co and HC whereas in BS3 catalytic converter is
available to reduce the formation of HC and CO. So less
emission of HC and co will take place in BS3

CC stands for Cubic centimeter. CC represents the total
volume of an engine cylinder. The engine which has more
CC , can produce more power than others.

injecter pressure is 220 kg/cm square

the range of two sroke engine is too high compare to the
four stroke engine be cause of each revalution one power in
two sroke engine . i canot see the 2 sroke engine in
car.power loss is more.

for maximum torque provied

it is weight of drive torque which is bolted to chassis of the car.

"SAE" STAND "SOCIETY OF AUTOMOTIVE ENGINEERS" (USA).

SAE20W40 :4WHEELER ENGINE,2 WHEELER ENGINE, GEAR BOX &CLUTCH.
SAE40W60 :GEAR BOX OF RWD & 4WD VEHICLE.

During the process of vulcanisation of rubber to make it
sheer resistant to make tyres out of it, a certain
proportion of carbon is mixed into it. Without this
procedure the tyres will not be able to withstand the
friction n stress of the road. This carbon is responsible
for giving tyres the characteristic black colour.. When
ozone combines with ultraviolet light from the sun, it
attacks the tire polymer. To prevent tires from rapidly
deteriorating, a sacrificial absorber is used, "carbon
black" - which, fittingly, makes tires black

it depends on pascal law. As the pressure in the system is the same, the force that the fluid gives to the surroundings is therefore equal to pressure x area. In such a way, a small piston feels a small force and a large piston feels a large force

Tuning: The adjutment of a system or circuit to bring the optimum correctness
Mapping: Making or design of maps

When we accelerate our vehicle, it provide more fuel into the cylinder from fuel injector. Yes you are right valve operating time is fixed bt in this short period of opening we provide more quantity of air-fuel mixture.